CMF#L

STEEL HOLLOW PISTON CYLINDERS SPRING RETURN

force: 10-100t

stroke: 8-160mm

max working pressure: 700bar

Features

All the CMF cylinder series are supplied with a smooth hollow saddle and the cylinder body, rod and bottom are threaded to facilitate the fixing and fitting of eventual accessories. The end of stroke nut has a wiper seal which prevents the penetration of dirt inside the cylinder. Cylinders are supplied with anti-corrosive treatment which is very effective to protect the central bore.

OPERATIONAL AREAS
These cylinders are recommended for tensioning and for the extractiong of pulleys, bushes and heat exchangers.They can also be used in both pulling and pushing operations by inserting either a bar or a cable through the hollow saddle. These cylinders are also supplied with the UE pullers

OPZIONI
L version, cylinders with aluminium body ( CMF###L### )

ACCESSORIES
ZTE threaded saddle Allows the fitting of threaded bars usually for extractors (UEC / UEG / UEZ / UET series).

STANDARD
Smooth hollow saddle prevents any risk of any possible rod deformation.

♦ EUROPRESS technical department is available to design special customised solutions.

♦ It’s important to drop the pressure inside the cylinder before disconnecting the quick coupler to avoid problems if re-inserting or lowering the load. In case some pressure persists it is possible to use the apposite tool KTS38 in order to lower the pressure in the couplers.

Selection chart

PUSHING FORCE	STROKE	EFFECTIVE AREA	OIL VOLUME	MODEL	CLOSED HEIGHT	Ø EXTERNAL VERSION N Ø EXTERNAL VERSION L	Ø PISTON	Ø ROD	COUPLER HEIGHT	Ø HOLLOW SADDLE	ROD PROJECTION	ROD INTERNAL THREAD	ROD THREAD DEPTH	Ø PCD MOUNTING HOLES	MOUNTING HOLES DEPTH	COLLAR THREAD	COLLAR THREAD LENGTH	Ø THROUGH HOLE	WEIGHT VERSION N	WEIGHT VERSION L	* Nominal value, see kN for the exact force
t* kN	mm	cm²	cm³	MODEL	A mm	D mm	E mm	F mm	H mm	J mm	K mm	O mm	P mm	U mm	V / Z mm	W mm	X mm	Y mm	kg	kg
10 123	8	17,6	14	CMF10N8	55	80 / –	55	38	–	–	–	–	–	–	–	–	–	21,5	2,3	–
	50		88	CMF10N50	132	74 / 75		40	19	34,5	1	M30 x1,5	16	50,8	2xM8 8	M74 x2	20	21	3,8	2,5
	80		141	CMF10N80	176	74 / 75		40	19	34,5	1	M30 x1,5	16	50,8	2xM8 8	M74 x2	20	21	4,8	3,1
20 230	50	32,9	164	CMF20N50	150	100 / 105	75	56	19	47,5	2	M40 x1,5	24	82,6	2xM8 10	M100 x2	20	28	7,8	5,3
	100		328	CMF20N100	221														10,7	7,4
	160		525	CMF20N160	305														14,1	9,5
22 212	8	30,3	24	CMF22N8	60	100 / –	75	55	–	–	–	–	–	–	–	–	–	33	3,5	–
30 334	50	47,7	239	CMF30N50	160	115 / 125	90	65	21	57,5	2	M48 x1,5	32	92,2	2xM10 12	M115 x2	20	34	10,5	8,1
	100		477	CMF30N100	233														14,5	11
	150		716	CMF30N150	303														18,1	13,6
60 590	75	84,3	632	CMF60N75	219	165 / 180	125	90	26	81,5	2	M72 x1,5	40	130,2	2xM12 16	M165 x4	25	54,5	28,9	21,4
60 590	150	84,3	1264	CMF60N150	331	165 / 180	125	90	26	81,5	2	M72 x1,5	40	130,2	2xM12 16	M165 x4	25	54,5	39,9	28,6
100 947	75	135	1015	CMF100N75	270	215 / 235	165	125	36	118	4	M102 x1,5	55	130	4xM12 15	M215 x4	35	80,5	59,3	44,6

Accessories ZTE threaded saddles

FOR USE WITH	a	k	j	p	y	o	kg
** CMF10 # # # #	20	4	34.5	16	3/4’’ – 16 UNC	M30x1,5	0.1
CMF20 # # # #	30	6	47.5	24	1’’ – 8 UNC	M40x1,5	0.25
CMF30 # # # #	39	7	57.5	32	1 ¼’’ – 7 UNC	M48x1,5	0.32
CMF60 # # # #	47	7	81.5	40	1 ⅝’’ – 5 ½ UNS	M72x1,5	0.85

applications

All EUROPRESS products are covered by a one year guarantee against any defects in materials or workmanship. This guarantee does not cover normal wear and tear, improper use or any applications not in compliance with our recommended instructions, or where the equipment is used with unsuitable fluids, modifications and/ or alterations (including those resulting from repair or attempted repair by persons not authorized by EURO PRESS PACK), or damage caused by transportation.

To report any flaw, defect, non conformity, and/or to claim action under this guarantee, the Customer shall inform EURO PRESS PACK in writing within 5 days after receipt of the goods, or in case of hidden defect, within 5 days after such defect has been discovered. Before returning the goods to EURO PRESS PACK for possible remedy under guarantee, the purchaser shall have received EURO PRESS PACK’s authorization . If EURO PRESS PACK is firmly convinced that its own product is defective, EURO PRESS PACK will provide free of charge for repair or replacement. The transport costs to and from EURO PRESS PACK are at the customer’s charge.

If the intervention of EURO PRESS PACK personnel or of our authorized distributors is requested on the site for installation of the replaced items (provided it is ascertained that they are covered by this guarantee) the costs of transfer of such personnel, their travelling hours and travel expenses are at the Customer’s charge, whereas only the actual working hours will be at the charge of EURO PRESS PACK or of its authorized distributor.

THE ABOVE GUARANTEE IS THE ONLY GUARANTEE ACKNOWLEDGED AND RECOGNIZED BY EURO PRESS PACK AND IT REPLACES ANY AND ALL OTHER EXPLICIT OR IMPLICIT GUARANTEES REGARDINGTHEPRODUCTSMANUFACTURED AND MARKETED BY EURO PRESS PACK, AS TO THEIR MARKETABILITY OR SUITABILITY FOR SPECIFIC APPLICATIONS.

IT IS HEREBY EXPRESSLY STATED THAT ANY CHARGES AND/OR LIABILITY OF EURO PRESS PACK ARE EXCLUDED REGARDING:

ANY ACCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY DEFECTIVE OR NON CONFORMING PRODUCTS, BY NEGLIGENCE OR OTHERWISE;
DAMAGE DUE TO OTHER CAUSES INCLUDING, BUT NOT LIMITED TO NEGLIGENCE OF EURO PRESS PACK;
ANY OTHER OBLIGATION OR LIABILITY DERIVING FROM BREACH OF CONTRACT OR OF GUARANTEE.

THIS GUARANTEE WILL NOT BE EFFECTIVE IN CASE OF EVEN PARTIAL DEFAULT IN PAYMENT FOR THE SUPPLIED GOODS, INCLUDING INVOICES FOR TECHNICAL ASSISTANCE SERVICES.

The maximum amount payable by EURO PRESS PACK for damages will at all events be limited to the actually paid purchase price and shall therefore never exceed this price.

I In case of goods lost during transport, please contact the company within 30 days of loss: sales@europresspack.it

QUALITY CERTIFICATION
Euro Press Pack has always been a Company very attentive to quality norms. This means that both the design of our products than their manufacturing are planned considering the Good Manufacturing Practice.All necessary controls are made to grant our customers the highest possible quality standard. In this way the final product is produced and checked according to the defined procedures and this assures that the quality system is efficient, controlled and proved.

QUALITY SYSTEM CERTIFICATE ISO 9001
Certification for design, manufacturing, marketing and repair of high pressure components.

ENVIRONMETAL SYSTEM CERTIFICATE ISO 14001
System certification for design and manufacture, through the various step of cutting, mechanical machining, surface treatments, painting, assembly, testing, packing and dispatch, sales and service of high pressure hydraulic fluid components.

ANSI B30.1
All cylinders comply to the standard laid down by the American National Standards institute (apart from CGS#P#, CGG#P#, and CGR cylinders).

EN 60204-1
The electric parts of the machines are made according the standard of EN 60204-1.

SAE 100R10
The 700 bar hoses exceed this norm.

Direttive CE 2006/42/CE – CE 2006/95/CE – CE 2004/108/CE
All our power packs conform the CE norm on the machine directive, low tension and electromagnetic compatibility.

CE mark.
All EUROPRESS products meet the European safety directives. Except certain systems or utensils which are designed for a specific use and are certified as machineries, all the cylinders, pumps and power packs of generic purpose are accompanied by certificates. The CE certification is responsibility of the construction of the machinery in which all the components are assembled.

READY DELIVERY

Thanks to our speedy deliveries you don’t have the urge to place a huge stock order to assure your customers a good service

CMF#L

STEEL HOLLOW PISTON CYLINDERS SPRING RETURN

Features

applications

Energy

constructions

Aerospace

Maintenances

READY DELIVERY